Custom Rectangular pipe adapter STL file 71x71 mm to 71x20 mm – transition: 50 mm 📦#4029

STL Download STL 1
Create a new model expert
from scratch search for a model
Rectangular duct connector provided as 3D STL file. Side A uses an internal cross-section of 71x71 mm (square), whereas side B is 71x20 mm (rectangular). The sleeve on side A provides an insertion length of 20 mm, and the sleeve on side B 70 mm. The transition section runs for 50 mm and the overall length is 140 mm, sleeves included. The ends are left without chamfers, with sharp inner and outer edges.
Generation date: 2025-11-29
3D Model Rectangular pipe adapter STL file 71x71 mm to 71x20 mm – transition: 50 mm

3D model download

Free
  • rectangular-to-rectangular-duc_model4029-nb0_dd{id}.stl : 47.7 Ko
STL Mesh quality : Linear deflection 0.0005 Angular deflection 0.05
No compliance warranty No compliance warranty
(Internal and private use, non-commercial – no distribution – no derivatives)
Safe download
Instant .zip download — no email, no account

Values for this model

This model was generated by the Rectangular-to-rectangular duct adapter template, with the following values:
Parameter Value
#1 side A internal width 71 mm (≃2.80 in)
#2 side A internal height 71 mm (≃2.80 in)
#3 sleeve length on side A 20 mm (≃0.79 in)
#4 side B internal width 71 mm (≃2.80 in)
#5 side B internal height 20 mm (≃0.79 in)
#6 sleeve length on side B 70 mm (≃2 3/4 in)
#7 thickness 2 mm (≃0.08 in)
#8 transition length 50 mm (≃1.97 in)
#9 Y offset 0 mm (0 in)
#10 Z offset 0 mm (0 in)
#11 end chamfers none
Metadata Value
external width on side A 75 mm (≃2 15/16 in)
external height on side A 75 mm (≃2 15/16 in)
external width on side B 75 mm (≃2 15/16 in)
external height on side B 24 mm (≃15/16 in)
total length 140 mm (≃5 1/2 in)
illustration of the parameters
Parameter overview

Labels are used in the naming of the downloaded 3D files.

Parameter Label
#1 side A internal width widRA
#2 side A internal height heiRA
#3 sleeve length on side A lenSA
#4 side B internal width widRB
#5 side B internal height heiRB
#6 sleeve length on side B lenSB
#7 thickness thi
#8 transition length tra
#9 Y offset ofsY
#10 Z offset ofsZ
#11 end chamfers cha

Related 3D models

To search for a model based on your own parameters, go to the template page Rectangular-to-rectangular duct adapter 

Rectangular duct adapter STL file 100x60 mm to 100x60 mm – transition: 20 mm (📦 #6424)

1 object(s) - format STL
Rectangular duct adapter STL file 100x60 mm to 100x60 mm – transition: 20 mm
Rectangular pipe adapter provided as 3D STL file. Side A and side B share the same internal cross-section, 100x60 mm, with a rectangular profile. The sleeve on side A provides an insertion length of 30 mm, and the sleeve on side B 70 mm. Between the two sleeves, the transition section adds 20 mm, giving an overall length of 120 mm. The ends are left without chamfers, with sharp inner and outer edges.
Parameter Value Unit
side A internal width 100 mm
side A internal height 60 mm
sleeve length on side A 30 mm
side B internal width 100 mm
side B internal height 60 mm
sleeve length on side B 70 mm
thickness 2 mm
transition length 20 mm
Y offset 0 mm
Z offset 0 mm
end chamfers none

Rectangular tube adapter STL file 100x100 mm to 35x35 mm – transition: 30 mm (📦 #4994)

1 object(s) - format STL
Rectangular tube adapter STL file 100x100 mm to 35x35 mm – transition: 30 mm
Rectangular pipe adapter downloadable as STL 3D file. The internal cross-section on side A is 100x100 mm (square), while side B is 35x35 mm (square). On side A, the sleeve length is 30 mm, and on side B it is 50 mm. The transition section between the two sides is 30 mm long, for an overall length of 110 mm (side A sleeve, transition and side B sleeve). The internal edges at the ends are chamfered to help guide the duct during insertion.
Parameter Value Unit
side A internal width 100 mm
side A internal height 100 mm
sleeve length on side A 30 mm
side B internal width 35 mm
side B internal height 35 mm
sleeve length on side B 50 mm
thickness 2 mm
transition length 30 mm
Y offset 0 mm
Z offset 0 mm
end chamfers inside

Rectangle-to-rectangle duct adapter STL file 96x51.2 mm to 40x26.2 mm – transition: 55 mm (📦 #4478)

1 object(s) - format STL
Rectangle-to-rectangle duct adapter STL file 96x51.2 mm to 40x26.2 mm – transition: 55 mm
3D STL file for rectangular vent adapter. The internal cross-section on side A is 96x51.2 mm (rectangular), while side B is 40x26.2 mm (rectangular). The sleeve insertion length is the same on both sides, 30 mm. Between the two sleeves, the transition section adds 55 mm, giving an overall length of 115 mm. The ends are left without chamfers, with sharp inner and outer edges. An offset of 12.5 mm along the Z axis is applied to side B with respect to side A.
Parameter Value Unit
side A internal width 96 mm
side A internal height 51.2 mm
sleeve length on side A 30 mm
side B internal width 40 mm
side B internal height 26.2 mm
sleeve length on side B 30 mm
thickness 2 mm
transition length 55 mm
Y offset 0 mm
Z offset 12.5 mm
end chamfers none

Rectangular duct adapter STL file 91.2x46.4 mm to 40x21 mm – transition: 55 mm (📦 #4479)

1 object(s) - format STL
Rectangular duct adapter STL file 91.2x46.4 mm to 40x21 mm – transition: 55 mm
Rectangular duct connector downloadable as STL 3D file. Side A offers an internal cross-section of 91.2x46.4 mm (rectangular) and side B uses 40x21 mm (rectangular). Each sleeve provides an insertion length of 30 mm. Between the two sleeves, the transition section adds 55 mm, giving an overall length of 115 mm. Inner and outer edges at both ends are left unchamfered. An offset of 12.7 mm along the Z axis is applied to side B with respect to side A.
Parameter Value Unit
side A internal width 91.2 mm
side A internal height 46.4 mm
sleeve length on side A 30 mm
side B internal width 40 mm
side B internal height 21 mm
sleeve length on side B 30 mm
thickness 2 mm
transition length 55 mm
Y offset 0 mm
Z offset 12.7 mm
end chamfers none

Rectangular pipe adapter STL 3D file 96x51.2 mm to 40x23.2 mm – transition: 60 mm (📦 #4438)

1 object(s) - format STL
Rectangular pipe adapter STL 3D file 96x51.2 mm to 40x23.2 mm – transition: 60 mm
Rectangular duct connector downloadable as STL 3D file. The internal cross-section on side A is 96x51.2 mm (rectangular), while side B is 40x23.2 mm (rectangular). The sleeve insertion length is the same on both sides, 30 mm. The transition section runs for 60 mm and the overall length is 120 mm, sleeves included. No chamfers are applied at the ends; both inner and outer edges remain sharp. Side B is offset by 24 mm along the Z axis relative to side A.
Parameter Value Unit
side A internal width 96 mm
side A internal height 51.2 mm
sleeve length on side A 30 mm
side B internal width 40 mm
side B internal height 23.2 mm
sleeve length on side B 30 mm
thickness 2 mm
transition length 60 mm
Y offset 0 mm
Z offset 24 mm
end chamfers none

Rectangular duct adapter STL 3D file 96x51.2 mm to 40x26.2 mm – transition: 55 mm (📦 #4439)

1 object(s) - format STL
Rectangular duct adapter STL 3D file 96x51.2 mm to 40x26.2 mm – transition: 55 mm
Rectangular duct transition downloadable as STL 3D file. The internal cross-section on side A is 96x51.2 mm (rectangular), while side B is 40x26.2 mm (rectangular). Both side A and side B sleeves share the same insertion length of 30 mm. Between the two sleeves, the transition section adds 55 mm, giving an overall length of 115 mm. Inner and outer edges at both ends are left unchamfered. Relative to side A, side B is shifted by 25 mm along the Z axis.
Parameter Value Unit
side A internal width 96 mm
side A internal height 51.2 mm
sleeve length on side A 30 mm
side B internal width 40 mm
side B internal height 26.2 mm
sleeve length on side B 30 mm
thickness 2 mm
transition length 55 mm
Y offset 0 mm
Z offset 25 mm
end chamfers none

Rectangular pipe adapter STL 3D file 77x34 mm to 77x34 mm – transition: 30 mm (📦 #4959)

1 object(s) - format STL
Rectangular pipe adapter STL 3D file 77x34 mm to 77x34 mm – transition: 30 mm
Rectangular duct adapter exported as STL 3D file. On both side A and side B, the internal cross-section is 77x34 mm, with a rectangular geometry. Both side A and side B sleeves share the same insertion length of 30 mm. Between the two sleeves, the transition section adds 30 mm, giving an overall length of 90 mm. Internal chamfers are added at the ends to make assembly and duct insertion easier.
Parameter Value Unit
side A internal width 77 mm
side A internal height 34 mm
sleeve length on side A 30 mm
side B internal width 77 mm
side B internal height 34 mm
sleeve length on side B 30 mm
thickness 2 mm
transition length 30 mm
Y offset 0 mm
Z offset 0 mm
end chamfers inside

Rectangular duct adapter STL file 96x30 mm to 80x20 mm – transition: 20 mm (📦 #4436)

1 object(s) - format STL
Rectangular duct adapter STL file 96x30 mm to 80x20 mm – transition: 20 mm
3D STL file for rectangular adapter. Side A offers an internal cross-section of 96x30 mm (rectangular) and side B uses 80x20 mm (rectangular). The sleeve insertion length is the same on both sides, 20 mm. Between the two sleeves, the transition section adds 20 mm, giving an overall length of 60 mm. No chamfers are applied at the ends; both inner and outer edges remain sharp.
Parameter Value Unit
side A internal width 96 mm
side A internal height 30 mm
sleeve length on side A 20 mm
side B internal width 80 mm
side B internal height 20 mm
sleeve length on side B 20 mm
thickness 2 mm
transition length 20 mm
Y offset 0 mm
Z offset 0 mm
end chamfers none

Rectangular pipe adapter STL 3D file 100x30 mm to 80x20 mm – transition: 20 mm (📦 #3936)

1 object(s) - format STL (5.0/5) 1 vote(s)
Rectangular pipe adapter STL 3D file 100x30 mm to 80x20 mm – transition: 20 mm
3D STL file for rectangular duct adapter. The internal cross-section on side A is 100x30 mm (rectangular), while side B is 80x20 mm (rectangular). The sleeve insertion length is the same on both sides, 20 mm. The transition section between the two sides is 20 mm long, for an overall length of 60 mm (side A sleeve, transition and side B sleeve). The ends are left without chamfers, with sharp inner and outer edges.
Parameter Value Unit
side A internal width 100 mm
side A internal height 30 mm
sleeve length on side A 20 mm
side B internal width 80 mm
side B internal height 20 mm
sleeve length on side B 20 mm
thickness 2 mm
transition length 20 mm
Y offset 0 mm
Z offset 0 mm
end chamfers none

Rectangular tube adapter STL file 42x58.6 mm to 80.5x80.5 mm – transition: 30 mm (📦 #5063)

1 object(s) - format STL
Rectangular tube adapter STL file 42x58.6 mm to 80.5x80.5 mm – transition: 30 mm
Rectangular pipe adapter downloadable as STL 3D file. Side A uses an internal cross-section of 42x58.6 mm (rectangular), whereas side B is 80.5x80.5 mm (square). On side A, the sleeve length is 16 mm, and on side B it is 25 mm. The transition section runs for 30 mm and the overall length is 71 mm, sleeves included. No chamfers are applied at the ends; both inner and outer edges remain sharp.
Parameter Value Unit
side A internal width 42 mm
side A internal height 58.6 mm
sleeve length on side A 16 mm
side B internal width 80.5 mm
side B internal height 80.5 mm
sleeve length on side B 25 mm
thickness 2 mm
transition length 30 mm
Y offset 0 mm
Z offset 0 mm
end chamfers none

Rectangular pipe adapter STL file 38x54.6 mm to 80.5x80.5 mm – transition: 30 mm (📦 #5064)

1 object(s) - format STL
Rectangular pipe adapter STL file 38x54.6 mm to 80.5x80.5 mm – transition: 30 mm
Rectangular adapter exported as STL 3D file. The internal cross-section on side A is 38x54.6 mm (rectangular), while side B is 80.5x80.5 mm (square). On side A, the sleeve length is 16 mm, and on side B it is 25 mm. The transition section between the two sides is 30 mm long, for an overall length of 71 mm (side A sleeve, transition and side B sleeve). The ends are left without chamfers, with sharp inner and outer edges.
Parameter Value Unit
side A internal width 38 mm
side A internal height 54.6 mm
sleeve length on side A 16 mm
side B internal width 80.5 mm
side B internal height 80.5 mm
sleeve length on side B 25 mm
thickness 2 mm
transition length 30 mm
Y offset 0 mm
Z offset 0 mm
end chamfers none

Rectangular duct adapter STL 3D file 100x20 mm to 80x20 mm – transition: 20 mm (📦 #3876)

1 object(s) - format STL (4.0/5) 1 vote(s)
Rectangular duct adapter STL 3D file 100x20 mm to 80x20 mm – transition: 20 mm
Rectangular duct connector downloadable as STL 3D file. Side A uses an internal cross-section of 100x20 mm (rectangular), whereas side B is 80x20 mm (rectangular). Each sleeve provides an insertion length of 20 mm. The transition section between the two sides is 20 mm long, for an overall length of 60 mm (side A sleeve, transition and side B sleeve). Inner and outer edges at both ends are left unchamfered.
Parameter Value Unit
side A internal width 100 mm
side A internal height 20 mm
sleeve length on side A 20 mm
side B internal width 80 mm
side B internal height 20 mm
sleeve length on side B 20 mm
thickness 2 mm
transition length 20 mm
Y offset 0 mm
Z offset 0 mm
end chamfers none

Rectangle-to-rectangle duct adapter STL 3D file 96x51.2 mm to 50x26 mm – transition: 38 mm (📦 #4437)

1 object(s) - format STL
Rectangle-to-rectangle duct adapter STL 3D file 96x51.2 mm to 50x26 mm – transition: 38 mm
Rectangular conduit adapter provided as 3D STL file. Side A offers an internal cross-section of 96x51.2 mm (rectangular) and side B uses 50x26 mm (rectangular). The sleeve insertion length is the same on both sides, 20 mm. The transition section runs for 38 mm and the overall length is 78 mm, sleeves included. Wall thickness is minimal at 1 mm. Inner and outer edges at both ends are left unchamfered.
Parameter Value Unit
side A internal width 96 mm
side A internal height 51.2 mm
sleeve length on side A 20 mm
side B internal width 50 mm
side B internal height 26 mm
sleeve length on side B 20 mm
thickness 1 mm
transition length 38 mm
Y offset 0 mm
Z offset 0 mm
end chamfers none

Rectangle-to-rectangle duct adapter STL 3D file 50x50 mm to 43x43 mm – transition: 50 mm (📦 #8627)

1 object(s) - format STL
Rectangle-to-rectangle duct adapter STL 3D file 50x50 mm to 43x43 mm – transition: 50 mm
Rectangular conduit adapter exported as STL 3D file. The internal cross-section on side A is 50x50 mm (square), while side B is 43x43 mm (square). Both side A and side B sleeves share the same insertion length of 20 mm. The transition section between the two sides is 50 mm long, for an overall length of 90 mm (side A sleeve, transition and side B sleeve). No chamfers are applied at the ends; both inner and outer edges remain sharp.
Parameter Value Unit
side A internal width 50 mm
side A internal height 50 mm
sleeve length on side A 20 mm
side B internal width 43 mm
side B internal height 43 mm
sleeve length on side B 20 mm
thickness 3 mm
transition length 50 mm
Y offset 0 mm
Z offset 0 mm
end chamfers none

Rectangular duct adapter STL 3D file 50x50 mm to 43x43 mm – transition: 20 mm (📦 #8628)

1 object(s) - format STL
Rectangular duct adapter STL 3D file 50x50 mm to 43x43 mm – transition: 20 mm
3D STL file for rectangular duct fitting. Side A uses an internal cross-section of 50x50 mm (square), whereas side B is 43x43 mm (square). The sleeve insertion length is the same on both sides, 20 mm. Between the two sleeves, the transition section adds 20 mm, giving an overall length of 60 mm. No chamfers are applied at the ends; both inner and outer edges remain sharp.
Parameter Value Unit
side A internal width 50 mm
side A internal height 50 mm
sleeve length on side A 20 mm
side B internal width 43 mm
side B internal height 43 mm
sleeve length on side B 20 mm
thickness 3 mm
transition length 20 mm
Y offset 0 mm
Z offset 0 mm
end chamfers none

Rectangular pipe adapter STL file 122.3x60.3 mm to 116x56 mm – transition: 20 mm (📦 #7196)

1 object(s) - format STL
Rectangular pipe adapter STL file 122.3x60.3 mm to 116x56 mm – transition: 20 mm
3D STL file for rectangular duct connector. Side A uses an internal cross-section of 122.3x60.3 mm (rectangular), whereas side B is 116x56 mm (rectangular). The sleeve on side A provides an insertion length of 25 mm, and the sleeve on side B 30 mm. Between the two sleeves, the transition section adds 20 mm, giving an overall length of 75 mm. Internal chamfers are added at the ends to make assembly and duct insertion easier.
Parameter Value Unit
side A internal width 122.3 mm
side A internal height 60.3 mm
sleeve length on side A 25 mm
side B internal width 116 mm
side B internal height 56 mm
sleeve length on side B 30 mm
thickness 2 mm
transition length 20 mm
Y offset 0 mm
Z offset 0 mm
end chamfers inside

Rectangular tube adapter STL 3D file 122.3x60.3 mm to 116.3x56.3 mm – transition: 20 mm (📦 #7193)

1 object(s) - format STL
Rectangular tube adapter STL 3D file 122.3x60.3 mm to 116.3x56.3 mm – transition: 20 mm
Rectangular duct fitting provided as 3D STL file. The internal cross-section on side A is 122.3x60.3 mm (rectangular), while side B is 116.3x56.3 mm (rectangular). The insertion length on side A is 25 mm, while on side B it is 30 mm. The transition section runs for 20 mm and the overall length is 75 mm, sleeves included. The internal edges at the ends are chamfered to help guide the duct during insertion.
Parameter Value Unit
side A internal width 122.3 mm
side A internal height 60.3 mm
sleeve length on side A 25 mm
side B internal width 116.3 mm
side B internal height 56.3 mm
sleeve length on side B 30 mm
thickness 2 mm
transition length 20 mm
Y offset 0 mm
Z offset 0 mm
end chamfers inside

Rectangular duct adapter STL 3D file 38x58.6 mm to 80.5x80.5 mm – transition: 30 mm (📦 #5062)

1 object(s) - format STL
Rectangular duct adapter STL 3D file 38x58.6 mm to 80.5x80.5 mm – transition: 30 mm
Rectangular pipe adapter provided as 3D STL file. The internal cross-section on side A is 38x58.6 mm (rectangular), while side B is 80.5x80.5 mm (square). The insertion length on side A is 16 mm, while on side B it is 25 mm. The transition section runs for 30 mm and the overall length is 71 mm, sleeves included. The ends are left without chamfers, with sharp inner and outer edges. Side B is offset by 15 mm along the Y axis and 15 mm along the Z axis relative to side A.
Parameter Value Unit
side A internal width 38 mm
side A internal height 58.6 mm
sleeve length on side A 16 mm
side B internal width 80.5 mm
side B internal height 80.5 mm
sleeve length on side B 25 mm
thickness 2 mm
transition length 30 mm
Y offset 15 mm
Z offset 15 mm
end chamfers none

Rectangle-to-rectangle duct adapter STL 3D file 100x40 mm to 60x60 mm – transition: 50 mm (📦 #4205)

1 object(s) - format STL
Rectangle-to-rectangle duct adapter STL 3D file 100x40 mm to 60x60 mm – transition: 50 mm
Rectangular conduit adapter downloadable as STL 3D file. Side A offers an internal cross-section of 100x40 mm (rectangular) and side B uses 60x60 mm (square). The sleeve insertion length is the same on both sides, 20 mm. The transition section between the two sides is 50 mm long, for an overall length of 90 mm (side A sleeve, transition and side B sleeve). Inner and outer edges at both ends are left unchamfered.
Parameter Value Unit
side A internal width 100 mm
side A internal height 40 mm
sleeve length on side A 20 mm
side B internal width 60 mm
side B internal height 60 mm
sleeve length on side B 20 mm
thickness 3 mm
transition length 50 mm
Y offset 0 mm
Z offset 0 mm
end chamfers none

Rectangular duct adapter STL 3D file 38x54.6 mm to 80.5x80.5 mm – transition: 52 mm (📦 #5098)

1 object(s) - format STL
Rectangular duct adapter STL 3D file 38x54.6 mm to 80.5x80.5 mm – transition: 52 mm
Rectangular tube adapter provided as 3D STL file. Side A offers an internal cross-section of 38x54.6 mm (rectangular) and side B uses 80.5x80.5 mm (square). The sleeve on side A provides an insertion length of 16 mm, and the sleeve on side B 25 mm. The transition section between the two sides is 52 mm long, for an overall length of 93 mm (side A sleeve, transition and side B sleeve). No chamfers are applied at the ends; both inner and outer edges remain sharp. An offset of 26 mm along the Y axis is applied to side B with respect to side A.
Parameter Value Unit
side A internal width 38 mm
side A internal height 54.6 mm
sleeve length on side A 16 mm
side B internal width 80.5 mm
side B internal height 80.5 mm
sleeve length on side B 25 mm
thickness 2 mm
transition length 52 mm
Y offset 26 mm
Z offset 0 mm
end chamfers none

Rectangle-to-rectangle duct adapter STL file 38x54.6 mm to 80.5x80.5 mm – transition: 52 mm (📦 #5099)

1 object(s) - format STL
Rectangle-to-rectangle duct adapter STL file 38x54.6 mm to 80.5x80.5 mm – transition: 52 mm
Rectangular duct transition exported as STL 3D file. The internal cross-section on side A is 38x54.6 mm (rectangular), while side B is 80.5x80.5 mm (square). On side A, the sleeve length is 16 mm, and on side B it is 25 mm. The transition section between the two sides is 52 mm long, for an overall length of 93 mm (side A sleeve, transition and side B sleeve). Inner and outer edges at both ends are left unchamfered. Relative to side A, side B is shifted by 26 mm along the Z axis.
Parameter Value Unit
side A internal width 38 mm
side A internal height 54.6 mm
sleeve length on side A 16 mm
side B internal width 80.5 mm
side B internal height 80.5 mm
sleeve length on side B 25 mm
thickness 2 mm
transition length 52 mm
Y offset 0 mm
Z offset 26 mm
end chamfers none

Rectangular pipe adapter STL 3D file 77x34 mm to 34x77 mm – transition: 30 mm (📦 #4958)

1 object(s) - format STL
Rectangular pipe adapter STL 3D file 77x34 mm to 34x77 mm – transition: 30 mm
Rectangular adapter downloadable as STL 3D file. The internal cross-section on side A is 77x34 mm (rectangular), while side B is 34x77 mm (rectangular). Each sleeve provides an insertion length of 30 mm. Between the two sleeves, the transition section adds 30 mm, giving an overall length of 90 mm. Internal chamfers are added at the ends to make assembly and duct insertion easier.
Parameter Value Unit
side A internal width 77 mm
side A internal height 34 mm
sleeve length on side A 30 mm
side B internal width 34 mm
side B internal height 77 mm
sleeve length on side B 30 mm
thickness 2 mm
transition length 30 mm
Y offset 0 mm
Z offset 0 mm
end chamfers inside

Rectangular duct adapter STL 3D file 38x58.6 mm to 80.5x80.5 mm – transition: 30 mm (📦 #5061)

1 object(s) - format STL
Rectangular duct adapter STL 3D file 38x58.6 mm to 80.5x80.5 mm – transition: 30 mm
Rectangular duct fitting exported as STL 3D file. The internal cross-section on side A is 38x58.6 mm (rectangular), while side B is 80.5x80.5 mm (square). The insertion length on side A is 16 mm, while on side B it is 25 mm. The transition section runs for 30 mm and the overall length is 71 mm, sleeves included. The internal edges at the ends are chamfered to help guide the duct during insertion.
Parameter Value Unit
side A internal width 38 mm
side A internal height 58.6 mm
sleeve length on side A 16 mm
side B internal width 80.5 mm
side B internal height 80.5 mm
sleeve length on side B 25 mm
thickness 2 mm
transition length 30 mm
Y offset 0 mm
Z offset 0 mm
end chamfers inside

Rectangular pipe adapter STL 3D file 71x71 mm to 71x20 mm – transition: 50 mm (📦 #4028)

1 object(s) - format STL
Rectangular pipe adapter STL 3D file 71x71 mm to 71x20 mm – transition: 50 mm
Rectangular conduit adapter downloadable as STL 3D file. Side A uses an internal cross-section of 71x71 mm (square), whereas side B is 71x20 mm (rectangular). The sleeve on side A provides an insertion length of 20 mm, and the sleeve on side B 7 mm. The transition section between the two sides is 50 mm long, for an overall length of 77 mm (side A sleeve, transition and side B sleeve). No chamfers are applied at the ends; both inner and outer edges remain sharp.
Parameter Value Unit
side A internal width 71 mm
side A internal height 71 mm
sleeve length on side A 20 mm
side B internal width 71 mm
side B internal height 20 mm
sleeve length on side B 7 mm
thickness 2 mm
transition length 50 mm
Y offset 0 mm
Z offset 0 mm
end chamfers none

Rectangular tube adapter STL file 79x33 mm to 66.7x28 mm – transition: 20 mm (📦 #4047)

1 object(s) - format STL
Rectangular tube adapter STL file 79x33 mm to 66.7x28 mm – transition: 20 mm
Rectangular duct adapter downloadable as STL 3D file. The internal cross-section on side A is 79x33 mm (rectangular), while side B is 66.7x28 mm (rectangular). Each sleeve provides an insertion length of 10 mm. The transition section runs for 20 mm and the overall length is 40 mm, sleeves included. Inner and outer edges at both ends are left unchamfered.
Parameter Value Unit
side A internal width 79 mm
side A internal height 33 mm
sleeve length on side A 10 mm
side B internal width 66.7 mm
side B internal height 28 mm
sleeve length on side B 10 mm
thickness 2 mm
transition length 20 mm
Y offset 0 mm
Z offset 0 mm
end chamfers none

Rectangle-to-rectangle duct adapter STL file 200x20 mm to 100x50 mm – transition: 55 mm (📦 #4707)

1 object(s) - format STL
Rectangle-to-rectangle duct adapter STL file 200x20 mm to 100x50 mm – transition: 55 mm
Rectangular duct fitting provided as 3D STL file. Side A uses an internal cross-section of 200x20 mm (rectangular), whereas side B is 100x50 mm (rectangular). The sleeve insertion length is the same on both sides, 30 mm. Between the two sleeves, the transition section adds 55 mm, giving an overall length of 115 mm. Inner and outer edges at both ends are left unchamfered. An offset of 12.7 mm along the Z axis is applied to side B with respect to side A.
Parameter Value Unit
side A internal width 200 mm
side A internal height 20 mm
sleeve length on side A 30 mm
side B internal width 100 mm
side B internal height 50 mm
sleeve length on side B 30 mm
thickness 2 mm
transition length 55 mm
Y offset 0 mm
Z offset 12.7 mm
end chamfers none

Rectangular pipe adapter STL 3D file 110x110 mm to 80x80 mm – transition: 20 mm (📦 #3644)

1 object(s) - format STL
Rectangular pipe adapter STL 3D file 110x110 mm to 80x80 mm – transition: 20 mm
Rectangular tube adapter downloadable as STL 3D file. Side A uses an internal cross-section of 110x110 mm (square), whereas side B is 80x80 mm (square). Both side A and side B sleeves share the same insertion length of 30 mm. The transition section runs for 20 mm and the overall length is 80 mm, sleeves included. The internal edges at the ends are chamfered to help guide the duct during insertion.
Parameter Value Unit
side A internal width 110 mm
side A internal height 110 mm
sleeve length on side A 30 mm
side B internal width 80 mm
side B internal height 80 mm
sleeve length on side B 30 mm
thickness 3 mm
transition length 20 mm
Y offset 0 mm
Z offset 0 mm
end chamfers inside

Rectangle-to-rectangle duct adapter STL file 104x34 mm to 100x30 mm – transition: 50 mm (📦 #4929)

1 object(s) - format STL
Rectangle-to-rectangle duct adapter STL file 104x34 mm to 100x30 mm – transition: 50 mm
Rectangular pipe adapter downloadable as STL 3D file. The internal cross-section on side A is 104x34 mm (rectangular), while side B is 100x30 mm (rectangular). The insertion length on side A is 25 mm, while on side B it is 15 mm. The transition section runs for 50 mm and the overall length is 90 mm, sleeves included. The internal edges at the ends are chamfered to help guide the duct during insertion.
Parameter Value Unit
side A internal width 104 mm
side A internal height 34 mm
sleeve length on side A 25 mm
side B internal width 100 mm
side B internal height 30 mm
sleeve length on side B 15 mm
thickness 2 mm
transition length 50 mm
Y offset 0 mm
Z offset 0 mm
end chamfers inside